Termination Cap Cover for Direct Vent Fireplaces

Our Termination Cap Cover stops fireplace drafts instantly.

Made in the USAGuard your house against extreme temperatures, bugs and small critters entering though the termination cap of your direct vent fireplace. Our Termination Cap Cover is the perfect solution! Our cap cover is a double-sided, multi-layered industrialized-strength, lightweight solid (non-breathable vapor barrier) aluminum radiant barrier approximately 6.5 mils in thickness. We use RadiantGUARD® radiant barrier foil and insulation products which are beneficial in ANY application where the goal is to CONTROL HEAT. When placed between a source of heat and an area you wish to keep cool, the surface of our radiant barrier material reflects 97% of the radiant heat energy back towards the heat source keeping the intended area cooler. That's a significant amount of protection against unwanted heat gain in the summer and unwanted heat loss in the winter and results in lowered monthly utility bills. Overtime, these monetary savings add up and continue to provide energy savings for years to come. It is non-toxic, non-carcinogenic, fiber-free and is not affected by moisture or humidity. It is Class A/Class 1 fire rated and made is the USA. Lower your heating & cooling bills year-round! It's easy to install and easy to remove when you use your fireplace.

As an alternative, you can use the Flue-zee to cover the flue from the inside - just remove the glass front and install on the flue opening. Click here to learn about the Flue-zee Flue Cover.

Termination Cap Cover - Option One

Cap Size: 13 ½"w x 13 ½"h
Attaches By: ties
Made For: Square Horizontal Cap

Fits a Direct Vent Square Horizontal Termination Cap with the dimensions shown below. Four soft twist ties hold the cap cover securely. The front of the cover is lined with a ½" Energy Star approved polystyrene foam to protect the shield from sharp corner wear and tear and adds insulation. Be sure to measure your cap before ordering!

Direct Vent Fireplace Termination Cap Cover

Termination Cap Cover - Option Two

Cap Size: 10 ½"w x 13 ½"h
Attaches By: ties
Made For: Trapezoid Shaped Termination Cap or Termination Cap Shroud

Fits the Trapezoid Termination Cap or the Termination Cap Shroud shown below. Two/four soft twist ties hold the cap cover securely to the cap/shroud. An attached insert of 1/2" Energy Star approved polystyrene foam fits over the bottom screen area to close it off. The full top cover slides into place over the top. This cover features a full top to accommodate different top vent designs or the full shape of the shroud. 13 1/2" h x 10 1/2" w x 8" d. Be sure to measure your cap before ordering!

Termination Cap Cover for Direct Vent Fireplace

Termination Cap Cover - Option Three

Cap Size: 8"w x 20"h
Attaches By: ties
Made For: Lennox SV 4.5 HT-2 Termination Cap

Fits the Lennox SV 4.5 HT-2 Termination Cap shown below. Two soft twist ties hold the cap cover securely to the cap at the bottom on each side. An attached insert of ½" Energy Star approved polystyrene foam fits into the bottom screen area to close it off. This cover features an adjustable top that fits tightly over the large open upper deflector. Three bungee cords hold the top and side firmly in place. This cap has a 20" height from the bottom of the cover to the top of the deflector and is 8" wide. Be sure to measure your cap before ordering!

Direct Vent Fireplace Draft Stopper

Termination Cap Cover - Option Four

Cap Size: 8"w x 10⅝"h
Attaches By: magnets
Made For: Majestic Patriot / CFDV Series

Fits the Majestic Patriot / CFDV Series (from the Vermont Castings Group) Termination Cap shown below. Four strong neodymium magnets secure the cover to each side. Check your side mounting strip with a magnet - it is the only place on this cover that is magnetic. The rivets need to attract a magnet to hold the cover in place. An attached insert of ½" Energy Star approved polystyrene foam fits into the bottom screen area to close it off. This cap has a 10 ⅝" height from the bottom of the cover to the full height of the deflector and is 8" wide. Be sure to measure your cap before ordering!

Direct Vent Fireplace Drafts

Termination Cap Cover - Option Five

Cap Size: 11"w x 13 ½"h
Attaches By: magnets
Made For: Majestic Quartz Direct Vent Termination Cap

Fits the Majestic Quartz Direct Vent Termination Cap shown below. Four strong neodymium magnets secure the cover to each side. Check your side mounting strip with a magnet - it is the only place on this cover that is magnetic. The rivets need to attract a magnet to hold the cover in place. An attached insert of ½" Energy Star approved polystyrene foam fits into the bottom screen area to close it off. This cap has a 13 ½ " height from the bottom of the cover to the full height of the deflector (top of the upper fin), is 11" wide and 6 ½" deep. Be sure to measure your cap before ordering!

Direct Vent Fireplace Drafts

Termination Cap Cover - Option Six

Cap Size: 9"w x 9"d
Attaches By: magnets
Made For: Direct Vent Round Horizontal Termination Cap

Fits a Direct Vent Round Horizontal Termination Cap. The cover is 10" in diameter and 10" deep. Three strong neodymium magnets hold the cap cover securely. The front of the cover is lined with a ½" Energy Star approved polystyrene foam to protect the shield from wear and tear and adds insulation. Be sure to measure your cap before ordering! Please check the face cover with a magnet to be sure our cover will attach. If you have a different diameter and depth or a magnet does not adhere to your face plate, you can request a custom round cover.

Direct Vent Fireplace Drafts

Termination Cap Cover - Option Seven

Cap Size: 12 ½"w x 12 ½"h x 4 ½"d
Attaches By: magnets
Made For: Direct Vent Round Horizontal Termination Cap

Fits a Superior Brand 12 ½" x 12 ½" x 4 ½" Horizontal Termination Cap. The cover is 13" square and 5 ½" deep. Four strong neodymium magnets hold the cap cover securely. The front of the cover is lined with a ½" Energy Star approved polystyrene foam to protect the shield from wear and tear and adds insulation. Four side panels are reinforced with foil wrapped corrugated plastic. Be sure to measure your cap before ordering! Please check the 12 ½" frame of the cover with a magnet to be sure our cover will attach.

Direct Vent Fireplace Drafts

YOUR PILOT LIGHT MUST BE TURNED OFF TO USE THE TERMINATION CAP COVER

Termination Cap Cover for Direct Vent FireplacesEnclosed with each Termination Cap Cover is a wire tie on NO FIRE tag to be put on your pilot light. This is to be attached when you install the Termination Cap Cover and will alert any person lighting the pilot that the cover is still on. Houses still need to breathe a bit. Our cover is not a 100% seal. But it will definitely stop warm air in the summer and cold air in the winter.
Always remember - NO FIRES, NO PILOT LIGHTS WHEN TERMINATION CAP COVER IS IN PLACE.

Ordering Details

WAYS TO ORDER

ONLINE: The easiest way to order is in the box above.

BY PHONE: If you prefer, you can give us a call to order by phone - 215-817-8229

BY MAIL: If you'd like to order by mail with a check, please print our order form.

SHIPPING

All termination caps are shipped separately for a fee of $12.95 each to addresses in the U.S.A. NOTE: If magnetic vent covers are also ordered with the Termination Cap Cover, the shipping cost for the vent covers ($12.95) will be reimbursed.

RETURNS

Returns are accepted within ten (10) days of receipt. Shipping fees will not be reimbursed.

INTERNATIONAL ORDERS

For international orders, send us an email with the items and quantities that you want to purchase and your shipping address. Shipping costs will be calculated based on weight and location. We will send you an invoice for your order (including shipping). OR, place your order online above and we will contact you with a quote for the additional shipping cost.

Installation for Covers One, Two & Three

(Options Four, Five, Six and Seven use magnets)

To attach the cap cover, simply loop the soft twist tie through the last side vent and bend into a hook shape as shown. Dow rods inserted at the covers' edges hold the cover in place. Brass grommets and soft twist ties secure the cover to your cap. Slip the cover's brass grommets over the twist tie. Complete to step two on each side of the cover. When all sides are in place tighten all ties by twisting two or more times. Our Termination Cap Covers are custom made and fitted on the termination caps shown. The aluminum radiant barrier material is tough and can be re-smoothed to shape if crushed. The soft ties are strong and made for outdoor use. Instructions will be sent with each order.

Direct Vent Fireplace Cap Covers

YOUR PILOT LIGHT MUST BE TURNED OFF TO USE THE TERMINATION CAP COVER

Real Comments from Real People

Following are testimonials from our actual clients using Draft Decor's termination cap cover.

I just received the termination cap cover... why are you not in every fireplace store? This is amazing! Exactly what I needed. I live in a very high wind area and through the winter months I am with blankets on in my living room, no matter what the heat is set at. I have asked chimney cleaners for their advice and no one came up with a solution in five years. One guy even said to put a revolving cap on the outside of the vent to dissipate the wind??? I put it on as soon as I received the package today. It covers my vent exactly. Today is rather windy, a warm wind, but I felt the draft directly from the pipe and when I placed the vent cap on...nothing! I actually can't wait for winter again. Thank you for your prompt service and excellent product.
Linda

I wanted to let you know my order arrived all in good condition. I finally got the termination cap cover installed and I'm soooooo happy!!  I needed it very badly for a south-facing vent where the fireplace is in a tiny office room with multiple computers running all the time. With the sun beating down on the metal vent constantly, the room quickly becomes an oven! I don't really need the fireplace, even in the winter, so I've just shut it off completely now.  Since installing the cap cover, I've been able to actually keep the room at a reasonable temperature even on the hottest of days. I wish I'd done it years ago!! Could not be more pleased, and do hope that the vent cover will last for years and years.
Thanks,
Brenda Mondragon